Cambiar procesador HP dc5800 SFF

[SebanimationsHD]

Hola, resulta que quiero cambiar el procesador de mi HP dc5800 Small Form Factor, el cual tiene un Celeron E1500 a 2.20 GHZ, pero quiero saber si realmente se puede y cual le debería poner. O, en caso que no se pueda, como hacerle overclock

[GOLD_MASTER]

Hola @SebanimationsHD.

Processor

Intel Core 2 Duo Processors, Intel Core 2 Quad Processors, Intel Pentium Dual-Core Processors , Intel Celeron D Processors

Instrucciones de sustitución:

1. Prepare the computer for disassembly (Preparation for Disassembly).
2. Remove the access panel (Computer Access Panel).
3. Remove the heatsink (Heatsink).
4. Rotate the locking lever to its full open position (1).
5. Raise and rotate the microprocessor retainer to its fully open position (2).
6. Carefully lift the processor from the socket (3).

      ATENCIÓN:

   Do NOT handle the pins in the processor socket. These pins are very fragile and handling them could cause irreparable damage. Once pins are damaged it may be necessary to replace the system board.

   The heatsink must be installed within 24 hours of installing the processor to prevent damage to the processor’s solder connections.

   

To install a new processor:

1. Place the processor in its socket and close the retainer.
2. Secure the locking lever. If reusing the existing heatsink, go to step 3. If using a new heatsink, go to step 6.
3. If reusing the existing heatsink, clean the bottom of the heatsink with the alcohol pad provided in the spares kit.

      ATENCIÓN:

   Before reinstalling the heatsink you must clean the top of the processor and the bottom of the heatsink with an alcohol pad supplied in the spares kit. After the alcohol has evaporated, apply thermal grease to the top of the processor from the syringe supplied in the spares kit.

4. Apply the thermal grease provided in the spares kit to the top of the processor and install the heatsink atop the processor.
5. Go to step 7.
6. If using a new heatsink, remove the protective covering from the bottom of the heatsink and place it in position atop the processor.
7. Secure the heatsink to the system board and system board tray with the four captive screws and attach the heatsink control cable to the system board.

      ATENCIÓN:

   Heatsink retaining screws should be tightened in diagonally opposite pairs (as in an X) to evenly seat the heatsink on the processor. This is especially important as the pins on the socket are very fragile and any damage to them may require replacing the system board.

   NOTA:

After installing a new processor onto the system board, always update the system ROM to ensure that the latest version of the BIOS is being used on the computer. The latest system BIOS can be found at the HP Software and Drivers page.

Referencia: https://support.hp.com/mx-es/product/hp-compaq-dc5800-small-form-factor-pc/3658082/document/c013629...

Si le ha servido,marque el hilo como solucionado.

[Maké]

Puedes ver, desde ... 

https://h10057.www1.hp.com/ecomcat/hpcatalog/specs/provisioner/05/AK818AW.htm

En la página 2, puedes ver también ... http://h10032.www1.hp.com/ctg/Manual/c01362761

Nota : Overcloking no es una buena práctica, ya que se puede dañar, el Procesador, e inclusive el Motherboard.

Si piensas adquirir el procesador que sea un upgrade del que tienes, debes realizarlo, por personas capacitadas, por tratarse de un componente muy sensible a la carga estática.

La pasta térmica de muy buena calidad que podrás aplicarle a la gráfica y procesador, es ... Artic Silver 5, que puedes ver, desde ... http://www.arcticsilver.com/as5.htm